Free Practice Questions for Dell EMC D-NWG-FN-23 Exam

Question 1

What is the default PIM-SSM IP range?

A224.0.0.0/4

B224.0.0.0/24

C232.0.0.0/8

D232.0.0.0/4

Correct Answer: C. 232.0.0.0/8

Question 2

When configuring VRRP in tandem with VLT, what is the default VRRP mode?

Aactive-active

Bprimary-standby

Cactive-standby

Dmaster-backup

Correct Answer: D. master-backup

Question 3

Which command is used to create a non-default VRF instance?

Aip vrf

Bip vrf forwarding new-vrf

Cip vrf forwarding vrf-test

Dinterface ethernet 1/1/1

Correct Answer: A. ip vrf

Question 4

You have been asked to examine a BGP configuration for a co-worker who is having difficulty establishing BGP peering. The address shown is that of the neighbor's Lo0 interface. Given the configuration shown, what would be your recommendation?

S3(config-router-bgp-65042)# neighbor 192.168.32.1

S3(config-router-neighbor)# remote-as 65042

AModify the existing configuration to be:
S3(config-router-bgp-65042)# neighbor 192.168.32.1/24 S3(config-router-neighbor)# peer-as 65042

BAdd the following to the existing configuration: S3(config-router-neighbor)# update-source loopback 0 S3(config-router-neighbor)# no shutdown

CIssue the no shutdown command and verify that the BGP state is ESTABLISHED

DIssue the no shutdown command and verify that the BGP state is ACTIVE

Correct Answer: C. Issue the no shutdown command and verify that the BGP state is ESTABLISHED

Question 5

Two OS10 switches reside within a VLT domain with statically configured primary-priorities. The current primary peer, switch OS10-A, has a priority of 100, while the secondary peer, OS10-B, has a priority of 200.

If OS10-A reboots and comes back online, what roles will the VLT peers be assigned?

AOS10-A will be primary and OS10-B will be secondary.

BOS10-A will be secondary and OS10-B will be master.

COS10-A will be standby and OS10-B will be primary.

DOS10-A will be secondary and OS10-B will be primary.

Correct Answer: D. OS10-A will be secondary and OS10-B will be primary.

Question 6

How are ACLs processed?

ALIFO

BFIFO

CRandomly

DSequentially

Correct Answer: D. Sequentially

Question 7

What is required to enable ECMP in BGP?

AOSPF must install equal cost paths in the routing table for BGP to use ECMP.

BMaximum-paths and multipath-relax commands.

CSub-interfaces must be configured on the physical interface running BGP.

DECMP is not possible in BGP.

Correct Answer: B. Maximum-paths and multipath-relax commands.

Question 8

Which LSA types are used in a single area OSPF topology?

A4, 5 and 7

B1 and 7

C1, 2 and 5

D2, 3 and 5

Correct Answer: C. 1, 2 and 5

Question 9

On what does PBR base routing decisions?

ADijkstra Algorithm

BBatch traffic

CAdministrator-defined forwarding

DShortest path

Correct Answer: C. Administrator-defined forwarding

Question 10

When configuring a vrf instance for the management interface that has been in use, what step must be done first to configure it?

AConfigure a management route

BRemove the default route

CRemove all configured settings

DConfigure an IP Address

Correct Answer: C. Remove all configured settings